PART 1 - GENERAL

1.01	DESCRIPTION OF WORK
	A.	This section includes Premiere Wall-Mounted Trophy and Display Cases
	B.	This section includes Imperial Series Wall-Mounted Trophy and Display Cases
		
1.02	REFERENCED STANDARDS
	A.	ASTM-E 84
	B.	ASTM B221

1.03 	SUBMITTALS
	A.	Shop Drawings:  Provide shop drawings for each type of wall-mounted display
		or trophy case required.
	B.	Product Data:  Provide technical data for materials specified.  Include 
		Material Safety Data Sheets, when applicable.
	C.	Samples:
		1.  Manufacturer's color charts
		2.  Composition samples of material and trim to illustrate finish, color 
		     and texture.

1.04 	OPERATION & MAINTENANCE
	A.	Include data on regular cleaning, stain removal, and precautions.

1.05 	REGULATORY REQUIREMENTS
	A.	Conform to applicable code for flame/smoke rating in tackboards in 
		accordance with ASTM-E 84.

1.06 	QUALITY ASSURANCE
	A.	Provide all items in this section as manufactured by:
		Claridge Products and Equipment, Inc. 
		Harrison, Arkansas  72602-0910
		Phone:  870/743-2200;  Fax:  870/743-1908

1.07	FIELD CONDITIONS
	A.	Field measure prior to preparation of shop drawings and fabrication to 
		ensure proper fit.  

1.08	WARRANTY
	A.	Submit a standard warranty, stating when installed in accordance with 
		manufacturer's instructions and recommendations, Claridge trophy and 
		display cases are guaranteed for one year against defects in materials 
		and workmanship. Guarantee does not cover normal wear and tear, improper 
		handling, any misuse, or any defects caused by vandalism or subsequent 
		abuse.  Guarantee covers replacement of defective material but does not 
		include cost of removal or reinstallation.

PART 2 - PRODUCTS

2.01 	MANUFACTURERS
	A.	Premiere and Imperial Series Wall-Mounted Display and Trophy Cases as 
		manufactured by:  Claridge Products and Equipment, Inc., Harrison, Arkansas 
		72602-0910; Phone: 870-743-2200; Fax:  870-743-1908

2.02	MATERIALS
	A.	Premiere Wall-Mounted Trophy and Display Cases
		1.	Architect to select from Claridge Cork, Fabricork, Hook-Fab, 
			Designer Fabric and Tan Nucork tackable back panel or Walnut or 
			Oak grained low-pressure laminate finish back panel.
		2.	Standard sizes: 4’ x 3’; 4'x4'; 4' x 5'; 4'x6'; 4'x8'; 4'x10'; 
			4'x12'; 4'x16'. Special sizes on request.
		3.	Housing:  Perimeter trim is 1-1/2" x 2" extruded aluminum tube; 
			inside cabinet depth 13-3/4"; O.A. 16".
	B.	Imperial Series Wall Mounted Trophy and Display Cases
		1.	Architect to select from Claridge Cork, Fabricork, Hook-Fab, 
			Designer Fabric and Tan Nucork tackable back panel or Walnut or 
			Oak grained low-pressure laminate finish back panel.
		2.	Standard sizes:  3’ x 4’ x 7”; 4’ x 5’ x 7”; 4’ x 6’ x 7”; 
			4’ x 5’ x 10-3/4”; 4’ x 6’ x 10-3/4”; inside depth of 7” cases 
			is 5-1/8”; inside depth of 10-3/4” cases is 8-7/8”
		3.	Housing:  Perimeter trim is 1-1/4” x 3-1/4” extruded aluminum 
			with satin anodize finish.
		4.	Header Panel:  Architect to specify if 6” translucent plexiglas 
			header required.
	C.	Glass Doors:  Glass doors are 3/16" tempered, unless otherwise specified.
		1.	Sliding door cases have ground-in finger pulls, doors slide on 
			glides, and are fitted with flat key tumbler locks.
		2.	Premiere cases have three 6, 8, 10 or 12-inch wide (as specified) 
			adjustable glass shelves; 7-inch deep Imperials have 4-inch 
			shelves; 10-3/4-inch Imperials have 8-inch shelves.
		3.	Necessary brackets and shelf standards provided.
	D.	Metal Trim and Accessories:  Provide aluminum extrusions as manufactured by 
		Claridge Products and Equipment, Inc.  Trim shall be heavy gauge extruded 
		aluminum and shall meet or exceed ASTM B221 Alloy Standards.  Finish to be 
		etched and anodized satin finish.  
	E.	Colors:  As selected from manufacturer's standard colors.  Over 50 standard 
		tackboard colors to choose from.  Color charts furnished on request.
	F.	Options:  Color anodize or powder coat finish on trim; fluorescent lights
	
2.03	FABRICATION
	A.	Shop assembly: Provide factory assembled cases to requirements indicated 
		on shop drawings.
	B.	Units shall be of dimensions shown in details and in accordance with 
		manufacturer’s shop drawings, as approved by architect.
		
PART 3 -  EXECUTION

3.01	PROJECT CONDITIONS
	A.	Verify before installation that interior moisture and temperature 
		approximate normal occupied conditions.
	B.	Verify that floor and wall surfaces are prepared and ready to receive cases.

3.02	INSTALLATION
	A.	Deliver cases set up, made in one piece.  
	B.	Follow manufacturer's instructions for storage and handling of units before 
		installation.  
	C.	Install level and plumb, in accordance with manufacturer's recommendations.

3.03	ADJUST AND CLEAN
	A.	Verify that all accessories are installed as required for each unit.
	B.	At completion of work, clean glass surfaces, back panels and trim in 
		accordance with manufacturer's recommendations, leaving all materials 
		ready for use.

Close Window