PART 1 - GENERAL

1.01	DESCRIPTION OF WORK
	A.	This section includes sliding door, wall mounted display cases with wood frame 

1.02	REFERENCED STANDARDS
	A.	ASTM-E 84
	B.	ASTM B221

1.03 	SUBMITTALS
	A.	Shop Drawings:  Provide shop drawings for each wall mounted display case, 
		as required.
	B.	Product Data:  Provide technical data for materials specified.  Include 
		Material Safety Data Sheets, when applicable.
	C.	Samples:
		1.  Manufacturer's color charts
		2.  Composition samples of material and trim to illustrate finish, color 
		     and texture.

1.04 	OPERATION & MAINTENANCE
	A.	Include data on regular cleaning, stain removal, and precautions.

1.05 	REGULATORY REQUIREMENTS
	A.	Conform to applicable code for flame/smoke rating in tackboards in 
		accordance with ASTM-E 84.

1.06 	QUALITY ASSURANCE
	A.	Provide all items in this section as manufactured by:
		Claridge Products and Equipment, Inc. 
		Harrison, Arkansas  72602-0910
		Phone:  870/743-2200;  Fax:  870/743-1908

1.07	FIELD CONDITIONS
	A.	Field measure prior to preparation of shop drawings and fabrication to 
		ensure proper fit.  

1.08	WARRANTY
	A.	Submit a standard warranty, stating when installed in accordance with 
		manufacturer's instructions and recommendations, Claridge wood frame, wall 
		mounted display cases are guaranteed for one year against defects in 
		materials and workmanship.  Guarantee does not cover normal wear and tear, 
		improper handling, any misuse, or any defects caused by vandalism or 
		subsequent abuse.  Guarantee covers replacement of defective material but 
		does not include cost of removal or reinstallation.

PART 2 - PRODUCTS

2.01 	MANUFACTURERS
	A.	Display Cases, wall mounted with wood frame as manufactured by: 
		Claridge Products and Equipment, Inc., Harrison, Arkansas  72602-0910; 
		Phone:  870-743-2200; Fax:  870-743-1908

2.02	MATERIALS
	A.	No. 309 Wall Mounted Sliding Door Display Case
		1.	Select from back panels of Claridge Cork, Fabricork, Hook-Fab, 
			Designer Fabric or low-pressure laminate with walnut or oak grain 
			finish 
		2.	Standard sizes: 	
			a.	7" depth - 36" x 48", 48" x 60" and 48" x 72"; inside 
				cabinet depth is 5-1/8" 
			b.	10-3/4" depth - 48" x 60" and 48" x 72";  inside 
				cabinet depth is 8-7/8" (10-3/4" deep cases have 
				center mullion for added support.) 
		3.	Housing:  Perimeter trim is clear red oak in natural, medium or 
			dark finish
 	B.	Glass Doors:  Glass doors are 3/16" tempered, unless otherwise specified.
		1.	Sliding door cases have ground-in finger pulls, doors slide on 
			glides, and are fitted with flat key tumbler locks
	C.	Metal Trim and Accessories:  Provide aluminum extrusions as manufactured by 
		Claridge Products and Equipment, Inc.  Trim shall be heavy gauge extruded 
		aluminum and shall meet or exceed ASTM B221 Alloy Standards.  All aluminum 
		components are finished with bronze finish.
	D.	Colors:  As selected from manufacturer's standard colors.  Claridge Cork, 
		Fabricork, Designer Fabric, Hook-Fab and walnut or oak grain low-pressure 
		laminate finish available.  Over 50 standard tackboard colors to choose 
		from.  Color charts furnished on request.
	E.	Hanging Devices:  Angle hangers furnished, continuous top and bottom.
	F.	Options:  Fluorescent lights, genuine walnut wood with natural or oil 
		finish; mahogany with natural or stain finish; maple with natural finish; 
		or cherry with stain finish.  Wood finish color charts furnished on request.

2.03	FABRICATION
	A.	Shop assembly: Provide factory assembled cases to requirements indicated 
		on shop drawings.
	B.	Units shall be of dimensions shown in details or in accordance with 
		manufacturer’s shop drawings, as approved by architect.
		
PART 3 -  EXECUTION

3.01	PROJECT CONDITIONS
	A.	Verify before installation that interior moisture and temperature 
		approximate normal occupied conditions.
	B.	Verify that wall surfaces are prepared and ready to receive units.

3.02	INSTALLATION
	A.	Deliver factory built units completely assembled in one piece without 
		joints, wherever possible.
	B.	Follow manufacturer's instructions for storage and handling of units 
		before installation.  
	C.	Install level and plumb, with fasteners furnished, in accordance with 
		manufacturer's recommendations.

3.03	ADJUST AND CLEAN
	A.	Verify that all accessories are installed as required for each unit.
	B.	At completion of work, clean glass surfaces, tackboard panels and trim in 
		accordance with manufacturer's recommendations, leaving all materials ready 
		for use.

Close Window